Yesha Lab Equipments

This apparatus is used for determination of Flash point & Fire point of Petroleum Products except fuel oil with open cup flash below 80 deg. C as per specification IP 36 and IS: 1448

(P:69) 1969. The apparatus consist of a cup, heating plate to specific dimension thermometer clip & test flame attachment with swivel joint for passing over test liquid surface in the

prescribed manner, heating is control by means of energy regulator fitted to the apparatus.

Electrical Heating with Immersion Heating Elements and Dimmer stat for controlling the

• Sturdy construction
• Perfect reading
• Long working life

Precise, Hot Air Drying Better Mineral / Blanket Insulation for high Temperature & to avoid heat loss Silent Hot Air Blower, Unique design of Air Circulation provide through out

uniform Air movement Unique design of ventilation keeps the surface of the instruments

from being Burnt even when the instruments i.e. Oven Temperature maintained at 200°C Polish / Hair Line 304 grade S. Steel sheet interior, long operation, corrosion resistant Kanthal A-1 Super quality coil shaped & Air heater tubular model wound on side/on the back of the Oven for better accuracy Full feature with Digital Temperature Controller cum Indicator having Alarm facility (On Customer request) Toughened Glass view window to observe /Test the material without disturbing the Temperature condition of the chamber. Working Temperature required as per IS : ASTM is 163°C+- 1°C Provide with detachable metal shaft (Both for Loss on Heating / Thin Film Oven) Reduction gear is fitted from outside rotated by a vertical shaft having 5-6 RPM. Applications : For Bitumen Testing Loss of weight, softening Paint, Penetration Loss of wt. in Bitumen & Flux Oils (For Construction

Size: 150mm x 150mm x 700mm

100mm x 100mm x 500mm

Two standard sizes of Beam Moulds are offered for casting concrete specimens for flexural strength testing. These beam moulds are made of cast iron and are supplied complete with a

We are a supplier of civil and mechanical Lab equipment, like Cube testing machine, cube molds, Auto level, Total station, Oven, Rapid Moisture meter, etc.

• Robust construction
• Safety cut-off switch

We are a supplier of civil and mechanical Lab equipment, like Cube testing machine, cube molds, Auto level, Total station, Oven, Rapid Moisture meter, etc.

This apparatus is used to determine Softening point of Bitumen. It is that temperature at which a sample of bituminous material loaded by a 9.5mm dia steel ball, drops a specified distance when heated under specified conditions.

Specification : The apparatus consists of steel bracket with a sliding plate support. That support has two holes of 10mm dia on which a ring and ball guide can be kept. A central

hole on this plate is for inserting thermometer. Supplied with a glass beaker approximate

600ml, high and a hand stirrer and 2 Nos. 9.5mm dia steel balls. Electrical heating, with a

Generally the test is applicable to hot mix designs using bitumen and aggregates upto a maximum size of 25mm. In this method, the resistance to plastic deformation of cylindrical specimen of bituminous mixture is measured when the same is loaded at periphery at 5 cm per min. This test procedure is used in designing and evaluating bituminous paving mixes. The test procedure is extensively used in routine test programmers for paving jobs. There are two major features of the Marshall method of designing mixes namely, a) density – voids analysis b) Stability – flow tests. The marshall stability of mix is defined as a maximum load carried by a compacted specimen at a standard test temperature of 60ºC. The flow value is deformation the marshall test specimen under goes during the loading upto the maximum load, 0.25 mm units. In this test and attempt is made to determine optimum binder content for the type of aggregate mix and traffic intensity.

The apparatus consists of: 1) A loading unit motorized, capacity 5000kgf with two telescopic pillars and an adjustable cross head.

Limit switches are fitted inside to control upward or downward movement of the pillars. On-

off reversing switch and indicator lamps are on the front side while a hand wheel to manually move the pillars is on the right. The load frameStandard Accessories: Marshal Mould:3 Nos,

Capacity: 1000kN, 2000kN

Optional: Digital Compression Testing Machine with Single Gauge also Available

The Digital Compression Testing Machine has been designed to meet the need for a simple, economic and reliable means to test concrete for its compressive strength. The Digital

Indicator incorporates a 4-Digits display calibrated in Kilo Newton (KN) and preset to

With our in-depth knowledge of this domain, we are actively engaged in offering an excellent quality assortment of Bitumen Asphalt Testing Equipment.

Features:

Robustness

Easy to operate

Low maintenance

• Net Weight: 0.09g
• Size: 24.5(L)*8.3(up Dia.)*3.5(Down Dia.)Cm
• Material: PS for Cup, PP for Ring

Specification: Same as Vicat Needle Apparatus but in addition is fitted with a dashpot which facilities gentle lowering of the needles. Accessories:

Mild steel base plate 5 inches x 5 inches. Fulcrum mould, brass, 70mm i.d. base dia. x 60mm

i.d. top dia., 40 mm height. Note:1) Normally set of needles and mould which meet is requirements as per I.S. 5513 are supplied. While ordering please specify the specification

code of the instrument required. 2) Vicat needle apparatus for determining consistency of

24 Hour cycle from time of mixing.

b) Controlled 35oC or 100oC ±2oC Curing Temperature for concrete. c) Controlled 27oC ±

2oC Curing Temperature for grey cement. The tank has been designed to accommodate

As Per IS 2386 (P-III)

Specification : Specific Gravity is the ratio of the weight in air of a given volume of a material at a standard temperature to the weight in air of an equal volume of distilled water

at the same stated temperature. The Pycnometer Bottle can be used to test a wide range of

materials from clay to sand and gravel smaller than 10mm. It consists of 1kg Glass Jar with

Brass Cone, Locking Ring and Rubber Seal.

Used to determine grade of bitumen. The penetration tests determine consistency of bitumen for the purpose of grading. Depth in units 1/10 of millimeter to which a standard needle

having a standard weight will penetrate vertically in a duration of five seconds

at a temperature of 25 degree C determines penetration for gradation.

Specification : It consists of a vertical pillar mounted on a base provided with leveling screws. The head, together with dial plunger rod a cone (or needle) slides on a pillar and can

be clamped at any desired height. A rack and pinion and pointer assemble provides fine adjustment of needle or cone tip to sample. It incorporates a clutch mechanism. Which makes

reading of penetration and subsequent resetting a simple and accurate operation. The dial is graduated in 400 1/10 and the millimeter subdivisions and the needle pointer

against figures makes easy reading. Supplied with a bitumen penetration needle, ring weight one each 50 gms. and 100 gms. two sample containers.

Accessories: Penetration cone for empirical estimation of penetration of lubricating grease,

We are a supplier of civil and mechanical Lab equipment, like Cube testing machine, cube molds, Auto level, Total station, Oven, Rapid Moisture meter, etc.

A 6-litre Mixer Used in conjunction with an Iso Mantle, is suitable for mixing samples of asphalt. Bench mounting Mixer, 6 liter nominal capacity. Supplied with bowl, beater and

whisk. Motorized with two speed operated on 230 V A.C., Single Phase.

ISO Mantle Electric Heater: For use of Bench Mounting mixer. For 230 VAC.,50Hz, Single

Designed to test three specimens simultaneously. The machine consists of a carriage moving over a lead screw. An electric motor driven reduction gear unit ensures smooth constant
speed and continuous operation. The entire assembly is mounted with a stainless steel lined water bath completely encased in metal bound hardwood. It is equipped with an electric
pump circulator and heater. The temperature is controlled thermostatically. Two rates of travel i.e. 5 cm/min and 1 cm/min are provided. Suitable for operation on 230 V, 50 Hz, Single Phase, A.C. supply.